SeeedStudio presenta il Raspberry Pi Compute Module IO, la scheda I/O HAT per la serie Raspberry Pi C3 con modulo di elaborazione e funzionalità PoE grazie alli’nterfaccia M.2.
Caratteristiche tecniche
- Header GPIO Raspberry Pi, per il collegamento di HAT Raspberry Pi.
- Porta Ethernet con negoziazione automatica 10 / 100M, con PoE, abilitata.
- 4x porte USB consentono di collegare più dispositivi USB.
- 2x interfacce per telecamere CSI.
- Interfacce HDMI / DSI integrate per il collegamento di display.
- USB TO UART integrato, per il debug seriale.
- Interfaccia della ventola di raffreddamento, accensione automatica all’accensione o controllata da pin IO.
- Adotta SMPS isolato (alimentatore switching).
Specifiche
- Alimentazione: porta micro USB / porta Ethernet PoE.
- Ingresso alimentazione PoE: 37 V ~ 57 V CC-in.
- Potenza PoE: 5 V 2,5 A CC in uscita.
- Standard di rete: standard PoE 802.3af.
- Dimensioni: 114mm × 84.4mm.
- Dimensione del foro di montaggio: 3,2 mm.
Mappatura I/O – LED – Accessori (Datasheet in inglese)
1. Compute Module interface: for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
2. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
3. PoE enabled Ethernet port: 10/100M auto-negotiation, for connecting router or switch with PoE function
4. DSI interface: display ports, for connecting Raspberry Pi LCD
5. USB ports: 4x USB ports, for connecting USB devices
6. CSI interface: 2x CSI camera ports, for connecting Raspberry Pi Camera
7. HDMI port
8. USB TO UART interface: for serial debugging
9. USB SLAVE interface: allows you to burn system image into Compute Module 3/3+
10. Power port: 5V 2.5A
11. TF card slot (bottom side): insert a Micro SD card with the pre-burnt system, to start up Compute Module 3/3+ Lite variant
12. Cooling fan interface
13. LAN9514 (bottom side): fully-integrated USB hub and 10/100M Ethernet controller
14. Si3404 PoE power management chip (bottom side)
15. CP2102 USB TO UART converter
16. EP13 PoE power transformer
17. Optical isolator
18. Two LED indicators:
19. Red: Raspberry Pi power indicator
20. Green: Raspberry Pi operating status indicator
21. NET network indicator
22. VGx power config jumper: config the I/O level
23. UART output config:
24. Left: connect the CP2102 serial port and Raspberry Pi serial port
25. Right: disconnect the CP2102 serial port and Raspberry Pi serial port
26. Cooling fan config:
27. P34: the fan is program-controlled via P34 pin
28. EN: the fan is directly powered from 5V power supply
29. PoE config:
30. DIS: disable PoE
31. EN: enable PoE
32. PoE power voltage measuring pads
2. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
3. PoE enabled Ethernet port: 10/100M auto-negotiation, for connecting router or switch with PoE function
4. DSI interface: display ports, for connecting Raspberry Pi LCD
5. USB ports: 4x USB ports, for connecting USB devices
6. CSI interface: 2x CSI camera ports, for connecting Raspberry Pi Camera
7. HDMI port
8. USB TO UART interface: for serial debugging
9. USB SLAVE interface: allows you to burn system image into Compute Module 3/3+
10. Power port: 5V 2.5A
11. TF card slot (bottom side): insert a Micro SD card with the pre-burnt system, to start up Compute Module 3/3+ Lite variant
12. Cooling fan interface
13. LAN9514 (bottom side): fully-integrated USB hub and 10/100M Ethernet controller
14. Si3404 PoE power management chip (bottom side)
15. CP2102 USB TO UART converter
16. EP13 PoE power transformer
17. Optical isolator
18. Two LED indicators:
19. Red: Raspberry Pi power indicator
20. Green: Raspberry Pi operating status indicator
21. NET network indicator
22. VGx power config jumper: config the I/O level
23. UART output config:
24. Left: connect the CP2102 serial port and Raspberry Pi serial port
25. Right: disconnect the CP2102 serial port and Raspberry Pi serial port
26. Cooling fan config:
27. P34: the fan is program-controlled via P34 pin
28. EN: the fan is directly powered from 5V power supply
29. PoE config:
30. DIS: disable PoE
31. EN: enable PoE
32. PoE power voltage measuring pads
ATTENZIONE: la board Raspberry Pi CM3 non è inclusa nel kit.
Raspberry Pi Compute Module IO viene venduto ad un prezzo di 40 dollari circa.
Per ulteriori informazioni consultate il sito del produttore.
Fabrizio Bianchini
###Da sempre appassionato di tecnologia, soffro di insaziabile curiosità scientifica. Adoro sperimentare e approfondire le mie conoscenze sulle ultime novità sul mercato in termini di hardware, alta tecnologia e videogiochi. Attratto e coinvolto nella prototipazione hardware dalla piattaforma Arduino, Raspberry Pi e Nvidia Jetson.### ###Always passionate about technology, I am suffering from insatiable scientific curiosity. I love experimenting and deepening of my knowledge on the latest news on the market in terms of hardware, hi-tech and video games. Got attracted and involved in hardware prototyping by the Arduino platform, Raspberry Pi and Nvidia Jetson.###